Wide unbranded upholstery and curtain cloth arranged for an editorial textile note

Textile note

Specifying Kvadrat Textiles: A 7-Step Checklist Before You Approve Any Fabric Order

2026-11-20 · Jane Smith

When this checklist applies

Use this before you sign off on any Kvadrat fabric order headed for a commercial interior — hotel lobby seating, office curtains, restaurant banquettes, or public-space upholstery. Seven steps. Each one has a physical check, not a phone call. I run this on 200+ fabric approvals a year, and roughly 15–20% of first-submittal packages fail at least one step.

Quick context on me: I manage quality and brand compliance for a commercial interiors firm. Every fabric specification gets reviewed before it hits a client. I've been doing this for about six years, and the majority of problems I catch have nothing to do with the fabric being bad. They have to do with the spec being unclear.

If you're sourcing through Kvadrat specifically, these steps save you the most time. If you're comparing Kvadrat textiles against other mills, the same checks apply — the questions just get harder to ask.

Step 1: Lock down the final use case before you open a sample card

Sounds obvious. It isn't. "Upholstery" covers everything from a decorative bench cushion that sees 2,000 abrasion cycles over five years to a departure-lounge sofa that sees 50,000 in eighteen months. Kvadrat's own catalog splits these categories, but the split only helps if you know which bucket you're actually in.

Write down three things before touching samples:

  • How many people sit (or lean, or wipe hands) on it per day
  • How much direct sunlight the surface receives, and through what glass
  • Whether the space needs a fire certificate, and what standard applies

If you can't answer all three, you're not ready to sample. This is the step most people skip. (It's also the one that causes the most rework later.)

Step 2: Confirm fiber composition — lyocell, viscose, and wool behave nothing alike

This is where a lot of specification errors start. Kvadrat textiles span wool, polyester, cotton blends, and regenerated cellulose fibers. Two of those fibers get confused constantly: lyocell and viscose.

So — what is viscose fabric? Viscose is a regenerated cellulose fiber made by dissolving wood pulp in a chemical bath (usually sodium hydroxide and carbon disulfide). It's soft, drapes well, and takes dye beautifully. It's also weaker when wet and prone to shrink if the finisher doesn't stabilize it correctly. The manufacturing process has a solvent-recovery problem that some mills handle better than others.

Lyocell fabric characteristics are different in ways that matter at spec time. Lyocell is also regenerated cellulose, but the solvent (N-methylmorpholine N-oxide, or NMMO) gets recovered at roughly 99% in a closed loop. The fiber comes out stronger, with better wet strength than viscose, and it's less prone to shrinkage under proper finishing. It wicks moisture. It has a smoother hand. And — the part nobody puts on the spec sheet — it can be more prone to fibrillation (surface fuzzing) than viscose if washing and finishing aren't dialed in.

Neither fiber is "better." Viscose sits well in drapes and low-traffic accents. Lyocell holds up better in upholstery where the client actually plans to sit. Know which you're specifying before you compare anything else.

It's tempting to think "cellulose-based" means "interchangeable." But the wet-strength and fibrillation differences between viscose and lyocell will determine whether your fabric still looks right in month eight or month thirty.

Step 3: Verify the abrasion rating against real-world traffic, not the datasheet headline

Martindale abrasion testing (ASTM D4966 or ISO 12947) gives you a number — 20,000 cycles, 40,000, 80,000. That number only means something relative to traffic. Commercial seating typically wants 40,000+ Martindale cycles for heavy use. Domestic upholstery can get by on 20,000.

Two things the headline number won't tell you:

  • Whether the rating was measured on the warp, weft, or both directions
  • Whether it included pilling/fuzzing assessment after the abrasion cycles

I've approved fabric at 40,000 cycles that failed at month six — because the sample held up under Martindale but the backing delaminated in a humid lobby. The abrasion rating is a starting filter, not a finish line.

Step 4: Check light fastness separately for curtains and sun-exposed upholstery

Color fastness to light (ISO 105-B02) gets graded on a 1–8 scale (where 1–5 is common for most contract textiles). A grade of 5–6 is typically expected for curtains in daylight-facing windows. Below 4, the color will visibly shift within one summer.

Most spec sheets list a single light-fastness number. Ask whether it was measured through standard glass or behind UV-filtering glass, and at what humidity. The difference between a grade-5 and grade-5-in-a-different-test-method can be the difference between a color holding three years or eighteen months.

In 2023, we had a client reject 80 running meters of curtain fabric because the spec sheet listed a light fastness of 5, but the downstream test used a different exposure cycle than the one our lobby actually experienced. The mill hadn't done anything wrong — the spec sheet was just incomplete. We now require the full test-method citation on every curtain order. All of them. No exceptions.

Step 5: Require current flame-retardancy certification before you discuss price

Commercial fabrics often need to pass BS 5852 (UK), EN 1021 (EU), or NFPA 260 / CAL TB 117 (US). Certifications expire. They also sometimes cover only the outer fabric and not the combination with the foam or interlining.

Ask for three things:

  1. The certificate itself, with issue date and expiry date
  2. The exact test standard and year version
  3. Whether the result applies to the fabric alone or the finished composite

If the cert is older than two years, ask for the current re-test. If the cert covers "fabric only," check with your upholsterer on the foam/interliner combination. This is the single biggest cause of failed fire inspections that I've seen — the fabric passes, the assembly doesn't.

Step 6: Approve color using physical lab dips, never a screen

Color approval on a monitor is a guess. Even high-end calibrated displays will show a Pantone reference differently than a dyed yarn will render it. Ask for a physical lab dip — a small dyed swatch produced in the same dye lot process as the production run — and review it under the actual lighting of the installation space.

Industry color tolerance is generally Delta E < 2 for brand-critical colors. Between 2 and 4, trained observers will notice a shift. Above 4, most people will. Pantone's own Color Bridge guide notes that CMYK approximations of Pantone references can vary by substrate and press calibration — and the same logic applies to textiles: a Pantone reference translated to a dyed yarn will shift depending on the fiber, yarn count, and dye process.

I made a classic first-year error here: approved a color off a photo the mill sent, because the lab dip "wasn't ready yet" and the client was in a hurry. The production run came back visibly warmer than what I'd signed off. It cost us a $1,400 redo and pushed the install back eleven days. Now I don't approve a color without a physical dip in hand. Period.

Step 7: Test batch sample under the project's actual light before the full run ships

This is the step almost everyone skips. Your lab dip may look perfect in the studio. It will look different in a north-facing hotel lobby at 8 a.m. It will look different again under 3000K track lighting. And it will look different again after three months of UV exposure.

Order a 1–2 meter sample from the actual production lot (not a stock cutting), bring it to the site, and look at it at three times of day. Compare it against the approved lab dip. If the variance is visible under the real lighting conditions, stop the run. If it's not, approve the shipment.

This costs you maybe $40 in shipping and one site visit. It has saved me from three batch rejections in the last two years. Not glamorous. Effective.

Things to watch for (and the ones that caught me)

The "same spec" assumption. I assumed that when two production batches carried the same Kvadrat tariff code, they'd match within tolerance. Didn't verify. Turned out that dye-lot variance between batches ran over 1.5 Delta E on one wool blend, which is borderline visible in good light. Now every batch order gets a lab-dip comparison against the master standard. No exceptions.

The "it says high-performance" assumption. "High-performance" is a marketing category, not a testing standard. Two fabrics both marketed as high-performance can differ by 30,000 Martindale cycles and a full light-fastness grade. Ask for the test numbers, not the descriptor.

The "lyocell and viscose are interchangeable" assumption. They're not. Viscose will drape beautifully in a curtain that nobody touches. Lyocell will hold up better where hands and bodies actually contact the fabric. Specify based on the use case, not on which sample card looks nicer on your desk.

The "the mill will catch it" assumption. They might. But when they don't, it's your name on the submittal. Build the checklist habit before the first shipment, not after the first rejection.

None of this is complicated. It's just easy to skip when the schedule is tight and the client is pushing. Which is exactly when it matters most.

Jane Smith

Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a reply